Trying to give back a little..........

Just about everything in the test found in the student guide provided by HP
41366-SG-V7.31

Where are Advanced Memory Protection Options configured?
ACU
ADU
RBSU
ORCA

Which methods upgrade the System ROM on HP ProLiant servers? (Select two.)
A. Online ROM Flash
B. Offline ROM Flash
C. Automatic ROM Upgrade Utilily
D. ROM-based Setup Utilily (RBSU)
E. Option ROM Configuration for Arrays (ORCA)

What are two methods used to configure iLO 2? (Select two.)
A. iLORBSU
B. iLO Configuration CD
C.Array Configuration Utility
D. iLO Web-based interlace
E. press F1 during POST

Which step must be performed before installing a second processor in an HP ProLiant server?
A. Update the system ROM.
B. Upgrade the operating system.
C. Update the memory configuration.
D. Upgrade the SCSI controller ROM.

Which util[Iy enables the HP Embedded SATA Software RAID option on a ProLiant DL320 or ML31 0 Server?
ACU
ORCA
RBSU
SmartStart

Where can the Array Configuration Utility be accessed? (Select two.)
A. ORCA
B. RBSU
C. SmartStartCD
D. Systems Insight Display
E. HP Firmware Maintenance CD
F. remotely from System Management Homepage

Which step is recommended before installing the operating system on a new HP ProLiant server?
Select PXE boot on network adapters.
Execute ROM-based Setup Utility (RBSU).
Perform a low-level format of the hard disks.
Upgrade BIOS to the latest version of firmware.

A customer has decided to upgrade an existing ProLiant server by adding two additional processors. After doing so, they receive the following error message on POST:
“UNSUPPORTED PROCESSOR DETECTED. SYSTEM HALTED.”
How should you remedy this situation?
A, Run the RBSU to configure the new processors.
B. Replace the processors because they are defective.
C. Run the System Erase Utility to clear the error message.
D. Remove the new processors, upgrade the system ROM on the server, and reinstall them.

Indicate the correct sequence of steps for installing nonhot-pluggable devices.
Find the appropriate position.
Open the chassis cover.
Install the component.
Shut down the server.
Remove any placeholders.

Which statements are true’? (Select two.)
A. Hard drive firmware can only be updated in offline mode.
B. HP ProLiant servers have three system ROMs for redundancy.
C. HP Smart Array controllers can only be upgraded in offline mode.
D. SmartStart CD 7.x can be used to run the HP ROM Update Utility.
E. HP ProLiant Firmware Maintenance CD can be used to upgrade firmware in offline mode.

Which HP utility’ configures online spare memory in a ProLiant server?
Array Configuration Utility’ (ACU)
FROM-based Setup Utility’ (RBSU)
System Configuration Utility’ (SCU)
Online Memory’ Configuration Utility’ (OMCU)

How does the warranty differ between the 100 and 300 series ProLiant servers?
300 series servers have a 3-year warranty, 100 series have a 1-year warranty
300 series servers have a 1-year warranty, 100 series have a 3-year warranty
300 series servers have a 3-year warranty, 100 series have a 2-year warranty
300 series servers have a 2-year warranty, 100 series have a 1-year warranty

Which high-availability solution level is recommended for a mission-critical business continuity model?
A. 99.8%
B. 99.9%
C. 99.99%
D. 99.999%

99.999% uptime translates to how much downtime per year?
5.25 days
5.25 hours
5.25 minutes
5.25 seconds

Which bus connects AMD Opteron processors together?
A. InfiniBand
B. Northbridge
C. Profusion
D. HyperTransport

What must you doto recover from a failed ROM upgrade on a ProLiant server with a redundant ROM image?
A. Use the SmartStart CD to restore the corrupted target server system ROM.
B. Implement ROM disaster recovery procedures to regain serverfunctionalily.
C. Implement disaster recovery procedures using the Smart Components for ROM Elash.
D. If a redundant ROM image is present, disaster recovery procedures are not necessary.

How does HP communicate problems that could cause server damage as well as provide a resolution?
A. ActiveAnswers
B. QuickSpecs
C. Service Bulletin
D, ProLiant Install Guide

Which ofiline tools can locate service information about the HP ProLiant DL360 G5 server? (Select two.)
A. HPPartSurler
B. HP Firmware Maintenance CD
C. Performance Quick Reference Tool
D. HP Parts Reference Guide (HP PRG)
E. HP Onsite Agent’s Reference Set (OARS)

Which HP resource contains video clips of removal and replacement procedures?
A. HPPartSurler
B. HP Parts Reference Guide
C. HP Services Media Library
D. HP Multimedia Product Bulletin

Which resource provides information on LEDs and switches specific to the ProLiant server?
Quick Specs
HP SmartStart CD
ROM-based Setup Utilily (RBSU)
Setup and Installation Guide for the ProLiant server

Which HP Online Resource provides best practices, sizers, and white papers?
A. ActiveAnswers
B. Product Bulletin
C. HP Serce Advisory
D. Onsite Agent’s Reference Set

Which number should you use to order an upgrade for a ProLiant server?
option part number
spare part number
server serial number
assembly part number

Where can you view We Automatic Server Recovery (ASR) settings? (Select two.)
A. Inspect
B. RBSU
C. iLO Administration page
D. Integrated Management Log (IML)
E. System Management Home Page

Which ProLiant server feature reboots the server after a hardware failure?
A. ADU
B. ASR
C. RBSU
D. ORCA

Which default time is used for Automatic System Recovery (ASR) on HP ProLiant servers?
A. 5 minutes
B. 10 minutes
C. 15 minutes
D. 30 minutes

Which UPLs are valid to log into the System Management Homepage iSMH? (Select two.)
A. https://127.0.0.1:2381 (from the local system)
B. https://127.0.0.1:3988 (from the local system)
C. https://127.0.0.1:8080 (from the local system)
D. https://hostname:2381 (from a remote system)
E. https://hostname:3988 (from a remote system)
F. https://hostname:8080 (from a remote system)

Which statements are true regarding Version Control Repository Manager (VCRMY? (Select two.)
A. VCRM is part of ProLiant Support Pack.
B. VCRM can automatically download updates.
C. VCRM must have write access to its repository directory.
D. VCRM should be installed on each ProLiant server on the network.
E. VCRM gathers software and firmware versions from configured ProLiant servers.

Which HP management tool allows IT administrators to set performance thresholds?
A. ProLiant Support Pack (PSP)
B. Intelligent Networking Pack (INP)
C. System Management Homepage (SMH)
D. Vulnerability and Patch Management (VPM)

You want to determine if the battery on the array accelerator board has failed. Which online tool shows if the battery is in an error state?
A. ADU
B. ORCA
C. OARS
D. RBSU

Which event log monitors and reports events on the ProLiant 100-series servers?
A. IPMI event log
B. ADU event log
C. RBSU event log
D. sysmon event log

A customer has 40 ProLiantDL38O G5 servers in a server farm. It is difficult to manage drivers and agents for all these servers.
They want to establish a baseline on one server and force all other DL3SO G5 servers in the farm to conform to the baseline server. Which HP tool provides this ability?
A. HP Survey Utility
B. Windows Update
C. Version Control Agent
D. Version Control Repository Manager

Which HP utility’ displays recognized NICs and statistics regarding current state?
A. HP Offline Diagnostic Utility’
B. Integrated Management Log
C. Integrated Management Display
D, ProLiant Network Configuration Utility’

Which tasks can be quickly performed from the System Management Homepage (SMH)? (Select three .)
A. track server performance
B. configure and manage EVA storage
C. review integrated logs (IML, iLO, etc)
D. install third-parte application software
E. manage Windows performance output
F. update BIOS, drivers, and agents through the VCA

Which utilities help evaluate disk-oriented counters on ProLiant servers running Linux? (Selecttwo.)
A. top
B. vmstat
C. iostat
D, cat/proc/cpuinfo
E. cat/proc/diskstatistics

You suspect memory has been removed from a regional server. You ran the Insight Diagnostics Survey Utility before sending the server to the site.
What is the easiest way to identify exactly what has changed?
A. Have the regional office send the server back and run the Insight Diagnostics Survey Utility again locally.
B Capture a new Insight Diagnostics Survey and, one by one, check off the components until you find the discrepancy.
C. Capture a new Insight Diagnostics Survey and use the Compare Configurations tab to compare the outputs and see what is different.
D. Send the Insight Diagnostics Survey output to someone at the regional office and ask them to open the server and check off items until they find what is missing.

Which packs are part of HP ProLiant Essentials Value Packs? (Select three.)
A. Foundation Pack
B Rapid Deployment Pack
C. System Management Pack
D. Performance Management Pack
E. Integrated Lights-Out Advanced Pack
F. Array Configuration Management Pack

Which statements are true regarding device discovery in HP SIM? (Select three.)
A. HP SIM uses FTP to discover servers.
B. Administrators cannot manually add a device to HP SIM.
C. HP SIM uses the AppleTalk protocol for device discovery.
D. HP SIM can discover devices on the LAN and identify them.
E. HP SIM periodically scans the network to discover new devices.
F. HP SIM allows creating discovery filters to avoid adding certain types of devices.

Which features can be enabled with ProLiant Essentials Integrated Lig9ts-Out Advanced Pack? (Select three .)
A. Virtual RAlD
B. Virtual Graphical Console
C. Virtual Floppy and Virtual CD
D. Directory Services integration
E. Virtual Systems Insight Display
F. Flash recovery for failed ROM upgrades

What are types of full backup? (Select two.)
A. copy
B. system
C. normal
D. differential
E. incremental

A customer wants a solution that keeps their HP ProLiant server firmware and drivers up to date without having to interact directly with each server or hiring additional IT staff.
Which products accomplish this goal? (Select two.)
A. HP Version Control Agent
B. HP Rapid Deployment Pack
C. HP Remote Deployment Utility
D. HP Version Control Repository Manager
E. HP Vulnerability and Patch Management

What are the advantages of a copy backup? (Select two.)
A. It does not purge log files on the drive.
B. It purges the log files on the drive to reduce wasted space.
C. Data transfer rate is faster than a normal full backup of the system.
D. It resets the normal backup schedule so the next backup will be a full backup.
E. It does not reset the archive bit so there is no disruption to the normal backup schedule.

A customer asks you to set up backups on a system. They want a weekly full backup and daily backups that will back up all files that have changed since the previous full backup.
Which type of backup will back up all files that have changed since the previous full backup?
A. copy
B. normal
C. differential
D. incremental

Which processor family does a ProLiant DL385 server use?
A. Intel Xeon
B. HP PA-RISC
C. AMD Opteron
D. Intelltanium2

Which ProLiant server family is intended for maximum internal storage?
A. DL
B. CL
C. ML
D. BL

Which components can be included in a packaged cluster solution from HP? (Select three.)
A. DL380
B DL760
C. ML370
D. MSA30
E. MSA50
F. MSA500
D. MSA1000

For each server in the task, indicate the maximum number of available processor sockets
ML150
ML350
DL385
ML570
DL580
1 processor sockets
2 processor sockets
4 processor sockets
8 processor sockets

Which HP ProLiant 300 Series servers support mirrored memory? (Select two.)
A. DL360 G5
B. DL385 G2
C. ML330 G3
D. ML350 G5
E. ML370 G5

Which protocols do HP ProLiant servers use to communicate with internal drives? (Select three.)
A. FC
B. SCSI
C. SAS
D. FTP
E. ATA
F. FireWire
G. SATA

Which remote management Lights Out solution is integrated onto the System Board of an HP ProLiant server?
A. RIB
B. iLO2
C. RILOE
D. RILOE II

Which HP rack product can be shipped unassembled and boxed on a standard-size palette?
A. HP MCS
B. HP 4042
C. HP 5642
D. HP10642
E. HP10842

How many MSA1 000 controllers can be installed in an MSA1 000 enclosure?
A.1
B.2
C.3
D.4

How many servers can safely be extended at one time on a 10000-series rack?
A.1
B 2
C.3
D. depends on the vertical position of the component inside the rack

A customer plans to install a UPS in a rack. Where should the UPS be placed?
outside the rack
at the top of the rack
in the middle of the rack
at the bottom of the rack

Which remote Lights Out management device has an external power source?
iLO
iLO2
RILOE II
Lights-Out 100

Which RAID technology supports the failure of any two drives in the same RAID set at the same time?
A. RAID 0
B. RAID 1
C. RAID 5
D. RAID ADG (RAID 6)

How do you take stress off the processor when a system is heavily taxed due to excessive network I/O?
A. Upgrade the system memory.
B Replace the NIC with a faster NIC.
C. Use TCP/IP Offload Engine (TOE) on the integrated HP Multifunction NICs.
D. Install a second NIC and enable HP Teaming to allow more bandwidth for network I/O.

An HP ProLiant DL580 server is not performing well when running a memory-intensive application. You have determined that adding more memory will help.
Which tool should you use in Windows 2003 to establish a baseline to measure against later?
A. rmon
B. iostat
C.perfmon
D. task manager

The performance of a ProLiant server running Windows 2003 is much degraded. Which method does HP recommend to overcome the problem?
A. Add memory, disks, and processors until the problem is soved.
B. Run iostatto isolate impacted subsystems and fix them one by one.
C. Use the HP 6-step methodology to determine the cause and resolution.
D. Use Windows sysmon to identiN bottlenecks and make recommendations.

Which actions belong to the final step of the HP Troubleshooting Methodology? (Select two.)
A. replacing the hard drive
B updating virus database
C updating software and drivers
D. identilting the mode of a failure
E. developing an optimized action plan

Put the 6-step methodology in the correct sequence.
Collect data
Evaluate the data
Develop an action plan Execute the action plan
Determine whether problem solved
Implement preventive measures

You have just tested your fix and have determined that the problem is solved. Which step in the HP Troubleshooting Methodology are you on?
A. Step1
B. Step2
C. Step3
D. Step4
E. Step5
F. Step6

After collecting data, you realize that the Windows page file is being heavily used. Which subsystem should be upgraded first?
A. processors
B. memory (RAM)
C. hard disk drives
D. network interlace cards (NICs)

After researching poor server performance, you have established a baseline and have decided to add extra memory and disks. What is your next step based on the HP Troubleshooting Methodology?
A. Install both upgrades and then create a new baseline.
B. Install only one upgrade and then create a new baseline.
C. Install both upgrades and then compare against the baseline.
D. Install only one upgrade and then compare against the baseline.

You have finished troubleshooting and resolving a problem at a customer site. You decide to provide a report to the customer based on the sixth step of the HP Troubleshooting Methodology.
Which details should you include in this report? (Select two.)
A. recommendations of preventive measures to take
B. the root cause of the problem and the documented fix or fixes
C. recommendations of upgrades that would increase system performance
D. the root cause of the problem and the person or group that should be held responsible for causing it

Which components are covered under the standard HP prefailure warrants? (Select three.)
A. iLO
B. fans
C. UPS
D. memory
E. processors
F. hard disk drives
G. SCSI controllers